Initialising...
0.0
mm
← Back home / Router Table
Demo Mode
Bit Height
0.0mm
Target
0.0mm
Relative
0.0mm
0.0 mm
0.0mm
Not homed 100 mm max
Bit height entry
0 mm
7
8
9
4
5
6
1
2
3
.
0
⌫
GO
STOP
Nudge — Lift
0.1
0.5
1
2
5
10
Step: 2.0 mm
▲ RAISE
▼ LOWER
− 10 mm/s
20 mm/s
+ 10 mm/s
Reference positions
Set ref zeromark current as 0
Go ref zeroreturn to ref
Fully lowermove to 0 mm abs
Fully raisemove to 100 mm abs
⚡ Simulated demo — no hardware connected
Absolute
0.0mm
Target
0.0mm
Relative
0.0mm
Not homed 1200 mm
Position entry
0 mm
7
8
9
4
5
6
1
2
3
.
0
⌫
GO
STOP
Nudge — Fence
0.1
0.5
1
5
10
50
Step: 1.0 mm
◀ LEFT
RIGHT ▶
− 50 mm/s
50 mm/s
+ 50 mm/s
Home positions
Set abs homemark here as 0
Set rel homemark relative zero
Go abs homemove to 0 mm
Go rel homemove to rel zero
⚡ Simulated demo — no hardware connected
Status: At position Height: 0.0 mm Steps/mm: 80.0000
1
2
3
4
Lift moving...
Before you start — Lift axis
The lift will move to 50 mm, 25 mm, and 75 mm in sequence. After each move, measure the actual bit height above the table using a height gauge or calipers and enter it below.

The system calculates the corrected steps/mm, excluding any outlier measurement automatically.
Lift status
At position
Current steps/mm
80.0000
Measurement 1 of 3 — 50 mm point
The lift has moved to 50 mm. Measure the actual bit height and enter it below.
Commanded
50.0 mm
You measured
—
0mm
enter actual measured height
7
8
9
4
5
6
1
2
3
.
0
⌫
Measurement 2 of 3 — 25 mm point
The lift has moved to 25 mm. Measure the actual bit height and enter it below.
Commanded
25.0 mm
You measured
—
0mm
enter actual measured height
7
8
9
4
5
6
1
2
3
.
0
⌫
Measurement 3 of 3 — 75 mm point
The lift has moved to 75 mm. Measure the actual bit height and enter it below.
Commanded
75.0 mm
You measured
—
0mm
enter actual measured height
7
8
9
4
5
6
1
2
3
.
0
⌫
Lift calibration results
— steps/mm
Previous: — steps/mm  · 
✓ LIFT CALIBRATED New steps/mm: —
Lift returning to rest position.
Status: At position Position: 2.0 mm Steps/mm: 80.0000
1
2
3
4
Fence moving...
Before you start — Fence axis
The fence will move to 600 mm, 300 mm, and 900 mm in sequence. After each move, measure the actual distance from the bit centre to the fence and enter it below.

The system calculates the corrected steps/mm, excluding any outlier measurement automatically.
Fence status
At position
Current steps/mm
80.0000
Measurement 1 of 3 — 600 mm point
The fence has moved to 600 mm. Measure the actual distance from bit to fence and enter it below.
Commanded
600.0 mm
You measured
—
0mm
enter actual measured distance
7
8
9
4
5
6
1
2
3
.
0
⌫
Measurement 2 of 3 — 300 mm point
The fence has moved to 300 mm. Measure the actual distance from bit to fence and enter it below.
Commanded
300.0 mm
You measured
—
0mm
enter actual measured distance
7
8
9
4
5
6
1
2
3
.
0
⌫
Measurement 3 of 3 — 900 mm point
The fence has moved to 900 mm. Measure the actual distance from bit to fence and enter it below.
Commanded
900.0 mm
You measured
—
0mm
enter actual measured distance
7
8
9
4
5
6
1
2
3
.
0
⌫
Fence calibration results
— steps/mm
Previous: — steps/mm  · 
✓ FENCE CALIBRATED New steps/mm: —
Fence returning to rest position.